ASTM A Standard Specification for Tool Steels Alloy. 17 Sep ASTM A Standard Specification for Tool Steels Alloy1_调查/报告_表格/ 模板_实用文档。This standard is issued under the fixed. ASTM A Standard Specification for Tool Steel. On May 9, / ASTM, Standards · ASTM A Standard Specification for Tool Steel Alloy · Next Post.

Author: Voodootilar Yozshunos
Country: Lebanon
Language: English (Spanish)
Genre: Automotive
Published (Last): 5 November 2004
Pages: 352
PDF File Size: 11.81 Mb
ePub File Size: 10.58 Mb
ISBN: 465-5-74927-263-4
Downloads: 14256
Price: Free* [*Free Regsitration Required]
Uploader: Majin

D2 Tool Steel 1. S7 tool steel is normally tempered one and one-half hours to two hours for each inch of greatest crosssection.

Preheat to original tempering temperature Astk C minimum. About Us Founded inFuShun covers an area of square meters, annual sales volume of tons. Fushun Special Steel Co.

H11 tool steels have the higher toughness, with some reduction in wear resistance and temper resistance. Use hot work tool steel filler material or type filler material may be satisfactory for small repairs or welds away from working surface of tool.

Quenching in oil atsm an increased risk for dimensional changes and cracks. The material shall be made by an electric melting process. This is not an anneal, and after the forging is cold, it must be properly annealed.

ASTM A – 08() Standard Specification for Tool Steels Alloy

D3 Cold Work Steel 1. Miss Summer summer fushunspecialsteel.

AISI S7 steel has exceptional impact properties plus the highest hardenability of shock resisting grades of tool steel. It can be quenched in air, exhibiting minimal distortion on hardening.

ASTM A681 Standard Specification for Tool Steel

Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous versions of standard. Back to Top Applications S7 tool steel has an unusual combination of properties, making it suitable for an extremely wide range of tool and die work — where shock-resistance, medium hot-work properties, or ease of machining and heat-treatment are most important. The a81 temperature varies according to the intended use.


ASTM O2 steel is widely used for universal use.

Temper 25F 15C below original tempering temperature. Back to Top Workability Forging: It is recommended for both hot and cold shock applications such as rivet sets, chisels, punches, moil points, hot headers and gripper dies.

H10 tool steel is recommended for difficult hot work tooling applications. AISI P20 Steel Plate Material is a versatile, low-alloy tool steel that is characterized by good toughness at moderate strength levels. H13 Tool Steel is chromium hot-work tool steels.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Back to Top Welding: Founded inFuShun covers an area of square meters, annual sales volume of tons. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. The selection of a material for a particular application will depend upon design, service conditions, and desired properties.

The special purpose mold steel P20 steel plate is commonly used for plastic injection mold cavities and tooling. S7 tool steel also has medium hot work characteristics, making qstm a versatile tool steel for both cold and warm shock applications, as well as plastic molds that require high hardness. It has maximum shock resistance and high compression strength, which gives it good deformation resistance in use, while retaining good toughness.


ASTM A S7 Tool Steel Flat Bar

NAK80 steel is a precipitation or age-hardened mold steel with a uniform through hardness of approximately 40 HRC. S7 tool steel is easy to machine in the annealed condition and can be readily heat treated. Otai steel supplies NAK80 mold steel for high end plastic mold steel. S7 tool steel is also suited for short-run dies used in coldforming, blanking, and bending.

AISI H12 steel is a 4. Reanneal or temper F C for 4 hours after welding. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

1.2355 ASTM A681 S7 Tool Steel Flat Bar

H13 Tool Steel 1. L6 Tool Steel 1. Small, simple forgings can be cooled slowly in dry lime, ashes or other insulating material. P20 Steel Plate 1. Sales Manager for European, African, Asia market: D2 is very wear resistant but not as tough as lower alloyed steels. O1 Tool Steel 1. H10 Tool Steel is one chromium hot-work tool asgm that exhibits excellent resistance to softening sstm elevated temperature.

AISI S7 tool steel is a shock-resistant air hardening steel.