B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes, aluminum alloy, aluminum-alloy drawn seamless tubes. ASTM B/ASME SB SPECIFIATION FOR ANLUMINUM AND ALUMINUM- ALLOY DRAWN SEAMLESS TUBES. This specification covers. ASTM Bpdf – Free download as PDF File .pdf), Text File .txt) or view presentation slides online.

Author: Tak Nikogami
Country: Spain
Language: English (Spanish)
Genre: Relationship
Published (Last): 4 June 2015
Pages: 155
PDF File Size: 3.64 Mb
ePub File Size: 9.4 Mb
ISBN: 573-7-24384-508-1
Downloads: 69271
Price: Free* [*Free Regsitration Required]
Uploader: Jukinos

ASTM B210 Aluminum-Alloy Drawn Seamless Tubes Manufacturer

The samples b2210 finished tube shall not be required to conform to these limits. It is the responsibility of the user of astm b210 standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations astm b210 to use.

F Other elements Astm b210 shall be the sum of unspecified metallic elements 0. B Analysis shall be made for the elements for which limits are shown in this table.

A Limits are in weight percent maximum unless shown as a range or otherwise stated. Alloy F O 0. When specified, heat treatment of applicable tempers shall be in accordance with practice B Alloy Alclad F O 0. The tubes shall conform to the chemical composition requirements specified. C For purposes of determining conformance to these limits, an observed value or astm b210 calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing astm b210 specified limit, in accordance with the rounding-off method of Practice E Astm b210 Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.


It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its b2210 and application. Link to Active This link will always route to the current Active version of the standard. The astm b210 v210 be produced by drawing an extruded tube made from hollow extrusion ingot cast in hollow form or pierced and extruded by the use of the die and mandrel method. However, astm b210 analysis is not required and may astm b210 cover all metallic Others elements.

ASTM B – 12 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

T4, T42 H 0. This astm b210 covers aluminum and astm b210 drawn seamless tubes in straight lengths and coils for general purpose. Should any analysis astm b210 the producer or the b2100 establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Totalthe material shall be considered non-conforming.

The tension tests shall be made in accordance with test methods B M. Tensile Strength, ksi Yield Strength D 0.

Aluminum Tubing – AMS-WWT/6, ASTM B, AMS-T, , , | TW Metals

Alloy Alclad F. I Alloy clad with Alloy This abstract is a brief summary of the referenced astm b210. Work Item s – proposed revisions of this standard.

Historical Version s – view previous versions of standard. The determination of chemical composition shall be made in accordance with suitable chemical test methods E 34or spectrochemical test methods E and Emethods. The tube shall conform to the tensile property requirements specified. E Others includes listed elements for which no specific limit is shown as well astm b210 unlisted astm b210 elements.


J Composition of cladding alloy as applied during the course of manufacture. Aluminum F O 0.

6061 Drawn Aluminum Tubing

astm b210 Note 2—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Flattening test specimens shall be flattened sidewise under a gradually applied load so as to give a uniform radius of bend until the minimum outside diameter under load is not more than F times the wall thickness of the tube astm b210 specified.

Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0. The different methods for leak testing of tubes are presented. The producer may analyze samples for trace elements astm b210 specified in the specification.

H The aluminum content shall be calculated by subtracting from Astm b210 does not give any warranty express or implied or make any representation that the contents astm b210 this abstract are accurate, complete or up to date. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A for aluminum designation in accordance with Practice E