HTX Datasheet PDF Download – LCD Module, HTX data sheet. BOEHYDIS HTX LCD Screen ” XGA For Lenovo X60 X61 42T 42T | Computers/Tablets & Networking, Computer Components & Parts. Find great deals for IBM ThinkPad X61 LCD Screen Htx 42t Shop with confidence on eBay!.
|Published (Last):||3 January 2018|
|PDF File Size:||17.46 Mb|
|ePub File Size:||19.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
Removing the clip allows for a cleaner cut.
IBM ThinkPad X61 12.1 LCD Screen Ht121x01-101 42t0435
The backlight channel in the LCD panel is covered by thin pieces of inner white plastic frame. Shipping cost cannot be calculated. Customer Feedback Last Week Below are some customer feedback in the past 1 or 2 weeks. Learn More – opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc. Learn More – opens in a new window or tab. For what it’s worth, I’ve damaged exactly one of these connections in a decade of disassembling LCD panels.
Don’t worry if the boot tears or it’s necessary to extract it as multiple pieces. Unscrew the two black machine screws on the sides of the screen near the bottom that attach the metal outer frame to the inner plastic frame. Once it’s mounted in the panel, it will be able to dissipate heat more efficiently into the metal backlight bracket than it can into free air.
There is no danger to continuing to operate the LED backlight. Raise the metal outer frame up and away from the inner white plastic frame by a few millimeters, just enough to expose the backlight wires.
BOE HYDIS HTX Overview –
Replace for now the two machine screws fastening the LCD controller board to the frame. Be the first to write a comment. Skip to main content. Pull gently and slowly.
Reassemble the lid and enjoy the new backlight. Get the item you ordered or get your money back. Remove ht11x01 hard drive, then power the machine on. The image above shows the correct orientation of the cable.
The pieces of white and yellow tape removed in step 6 are circled in red. It sacrifices easily half the available brightness of the LEDs. Add to watch list. Well packaged, delivered ahead of initial delivery date. Fast and efficient service.
Unthread the backlight wires from the inner white plastic frame and pull them forward out from the panel. The official Hardware Maintenance Manuals describe and illustrate the lid disassembly process in detail:.
The clips wrap around the plastic inner frame, so it’s necessary to ht121z01 open a few of the hasps holding the outer metal and inner plastic frames together, separate the halves by a few millimeters, pull each clip free, cut it, return it to the plastic frame, then close the metal frame back into position.
The next few steps are optional to prevent any accidental short circuits between the LED supply and a grounded backlight bracket. Remove the two tiny black screws on the back of the panel that connect the backlight bracket to the two metal side-mounting clips one on each side. Remove one silicone boot from the left side of the CCFL tube, then slowly pull the tube and the other boot out from the right side using needle-nose pliers.
The CCFL backlight tube sits in a channel formed by the 1011 reflector bracket. When sliding the LED strip into place, the fit should be just a bit snug.
The inner surface of the bracket is electrically insulated by a plastic film, but the metal edges of the bracket are exposed. See terms – opens in a new window or tab.
BOEhydis HTX LCD ” XGA HTX
Great experience doing business with you. We’ll need to shim them so that they’re situated properly. Pay most careful attention to the flat sides along the top, back, and bottom. Breaking the backlight bracket ground connection The next few steps are optional to prevent any accidental short circuits between the LED supply and a grounded backlight bracket. The flexible plastic cables attaching the controller board to the glass LCD are strong; the heat-bonded connections to the board and LCD glass are not.
Polyester and teflon sheet are both available with adhesive backings, or make adhesive shims by applying a layer of adhesive transfer tape e. LCD panel after cutting backlight wires to allow easier extraction.
Countries Shipped We have shipped to over Countries worldwide since There’s not much to final assembly as the shimming process has already fitted the LED strip into the panel.
On non-tablet screens, pay special attention to the edges around the front of the panel.