RA PRESSURE TEMPERATURE CHART. PSIG F° PSIG F° PSIG F° PSIG F° PSIG F° PSIG F°. 12 RA. RA. RC. R RA. RA. R kPa psig. kPa psig. kPa psig. kPa psig .. for any refrigerant blend. PRESSURE / TEMPERATURE CHART. Refrigerant RA Pressure Temperature Chart – RA is an HFC and is commonly used in residential and light commercial HVAC equipment for air.

Author: Dasar Yor
Country: Timor Leste
Language: English (Spanish)
Genre: Marketing
Published (Last): 16 October 2008
Pages: 270
PDF File Size: 1.87 Mb
ePub File Size: 4.98 Mb
ISBN: 853-4-19070-898-2
Downloads: 74389
Price: Free* [*Free Regsitration Required]
Uploader: Dougrel

RA differs a lot from R in both chemical makeup and the tools needed to measure the pressures of RA.

Save my name, email, and website in this browser for the next time I comment. Imagine a room full of vapor and dew drops forming on the furniture.

Two-column PT charts are every bit as useful as the r410a pt chart ones. Just remember to keep track of the phase of the blend at the r410a pt chart you are interested: Since RA operates at higher pressure and a different type of oil is used than R separate gauges should be used to obtain pressures.

Upload your photos or documents here! Photo Uploads If you are human, leave this r4100a blank.

PT Chart – R410A

By using this form you agree with the storage and handling of your data by cbart website. Click here for a new search Print Email. Drop a file here or click to upload Choose File Maximum upload size: Zeotropic blends shift in composition during the boiling or condensing process see Figure 2. Currently, every manufacturer of residential r410a pt chart light commercial systems offer their main product line which uses RA refrigerant for their air r410a pt chart and heat pump systems.


Capacity Data Center Operation: Imagine a pot of liquid sitting on a stove; as it begins to boil it forms bubbles in the liquid.

Not the FAQ you were looking for? PT charts are most often used for three purposes: This gives RA a higher refrigeration capacity than R If the liquid column is used r410a pt chart, then the beginning of the coil will be the correct temperature, but the rest of the coil will be too warm.

When checking the subcool condition the technician will measure the temperature of the liquid line, the pressure at that point and subtract the measured temperature from the saturated temperature at the end of the condenser. Your email r410a pt chart will not be published.

Refrigerant Pressure – Temperature Chart

Traditional PT charts list the saturated refrigerant pressure, in psig, with a column for temperature down the left side. Because RA adds more efficiency to HVAC equipment makes it a lot more desirable for the environment in more than one way. If the r410a pt chart column is read directly at the desired temperature, then the end r410a pt chart the evaporator will be the correct temperature, but the re st of the coil will be too cold. R410a pt chart these blends, the vapor and liquid pressures are only separated by 1 or 2 psi.

Single-component refrigerants and azeotropes boil and condense at one temperature for a given pressure. The overall shift of temperature from one side of the heat exchanger to the other is called the temperature glide. Because the difference is quite small between the two values some manufacturers’ PT charts will only list one column for these blends.


Refrigerant RA Pressure Temperature Chart PT Table

See the About the Author page for information about the author of this article. R410a pt chart Optimize Data Center Operation: In the case of a blend, you Simply read the saturated temperature next to the pressure r410a pt chart the vapor dew point column of the chart. Cross-contamination of the oils can cause serious issues between the two types of systems and it is highly cchart to use separate gauges for service providers.

With the blend you read the saturated temperature next to the pressure in the liquid bubble point column of the chart.

Refrigerant Pressure – Temperature Chart

Superheat is checked by measuring the temperature of the vapor line, measuring the pressure, then subtracting the saturated temperature from the measured temperature. Change Data Center Operation: The changing composition of the liquid causes the boiling point temperature to shift as r410a pt chart. The temperature glide will cause different values for temperature at a given pressure, depending on how much refrigerant is liquid and r410a pt chart much is vapor.

PT charts for the zeotropic blends list two columns next to each temperature: