instruments approved for SAE J and those intending to perform SAE J A specific test protocol to compare new test equipment to those previously. SAE J (R) Performance Based Standard for Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus. SAE J and SAE J test method, the cutoff position is nm, the same as a filter consist of the type “S” Borosilicate both inner and outer. SAE J
|Published (Last):||20 October 2015|
|PDF File Size:||6.98 Mb|
|ePub File Size:||16.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
Automotive Materials Weathering Testing
Automotive Weathering testing standards include QUV: This practice covers three types of laboratory weathering exposure procedures for evaluating the effect of actinic radiation, heat, and moisture on sealants. This practice covers specific procedures and test conditions that are applicable for xenon-arc exposure of plastics conducted in accordance with Practices G and G Auditing Consulting Sourcing Training.
Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. In a few days or weeks, our UV tester can reproduce the damage caused by full-spectrum sunlight and rain that occurs over months or years in the field and is suitable for exposing large, three-dimensional parts or components.
Intertek performs weathering testing on automotive materials and components, such as plastics and composites. These test methods cover techniques to evaluate three types of staining that rubber may cause when in contact with, or in proximity to, another surface that may be light colored.
This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards.
SAE J – Impact Solutions
Validating the specifications, value and safety of your raw materials, products and assets. This specification covers nonvulcanized uncured rubber sheet made of EPDM ethylene-propylene-diene terpolymer or CR polychloroprene intended for use as watertight roof flashing xae to the weather. It describes exposures swe sunshine carbon arc, xenon arc, fluorescent ultraviolet light and condensation apparatus, and a twin carbon arc.
The chamber includes moisture through water spray, humidity and temperature conditioning for accelerated life testing of plastics and components.
ASTM D Standard Test Methods for Rubber Property—Staining of Surfaces Contact, Migration, and Diffusion These test methods cover techniques to evaluate three types of staining that rubber may cause when in contact with, or in proximity to, another surface that may be light colored. Xenon Arc Fading Lamp Test.
Need help or have a question? Automotive materials weathering testing is an essential part of the automotive materials industry, as it is important u2527 understand the influence of weather on the performance and durability of materials and components. This test method covers the method for the determination wae the durability of a sealant based on its ability to function in cyclic movement maintaining adhesion and cohesion after repeated exposure to laboratory accelerated weathering procedures.
Environmental extremes – indoor and outdoor – faced by these plastic materials range ase very dry to wet and humid, and from freezing cold to very hot conditions. Certification Formally confirming that your products and services meet all trusted external and internal standards. Dae Materials Weathering Testing Materials weathering testing by QUV and Xenon Arc plus consultancy services for j25227 plastics, metals, coatings, composites and compounds Automotive materials weathering testing is an essential part of the automotive materials industry, as it is important to understand sxe influence of weather on the performance and durability of materials and components.
This test method provides the general principles and procedures which are currently in use for determining the colorfastness to light of textile materials. Automotive Materials Weathering Testing. Automotive Weathering testing standards include. Automotive Material Testing Services: This practice covers the basic principles and operating procedures for using xenon arc light and water apparatus intended to reproduce the weathering effects that occur when materials are exposed to sunlight either direct or through window glass and moisture as rain or dew in actual use.
Polymers consist of homopolymer, copolymers, and elastomer compounded with or without the addition of impact modifiers ethylene-propylene rubber, polyisobutylene rubber, and butyl rubbercolorants, stabilizers, lubricants, or reinforcements. This guide covers the selection and use of test methods and procedures for testing industrial protective coatings.
Inspection Validating the specifications, value and safety of your raw materials, products and assets. To decide between our Xenon Arc chamber or our Short-Wave Weathering Tester for your specific requirements, refer to this article. Textiles-Tests for colour fastness- Part B This practice covers the basic principles and operating procedures for ultraviolet UV light aging with or without water of adhesive bonded joints having at least one glass or transparent adhered, using fluorescent UV see Method A or xenon-arc light sources see Method B.
GM P Procedures for Laboratory Accelerated Exposure of Automotive Materials These procedures are used to determine the resistance to degradation of automotive materials when subjected to artificial light sources. Assurance Testing Inspection Certification. This practice provides general procedures to be used when exposing nonmetallic materials in accelerated test devices that use laboratory light sources. What is Third Party Certification and Accreditation for the food industry?
ASTM D Standard Specification for Poly Vinyl Chloride Sheet Roofing This specification covers flexible sheet made from poly vinyl chloride resin as the primary polymer intended for use in single-ply roofing membranes exposed to the weather. By Admin November 12, Materials weathering testing by QUV and Xenon Arc plus consultancy services for automotive plastics, metals, coatings, composites and compounds.
Automotive Materials Weathering Testing
This test method provides the procedure for the exposure of textile materials of all kinds, including coated fabrics and products made thereof, in j2257 artificial weathering apparatus j25227 controlled conditions of test. Enabling you to identify and mitigate the intrinsic sas in your operations, supply chains and business processes. This practice covers test conditions and procedures for xenon-arc exposures according to Practices G and G for bituminous roofing and waterproofing materials.
This test method covers specific variations in the test conditions and procedures that shall be applicable when Practice G plus either Practice G, G, G, or G are employed for exposure of vulcanized rubber compounds. This specification covers polypropylene materials suitable for injection molding and extrusion. ASTM C Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures This test method covers the method for the determination of the durability of a sealant based on its ability to function in cyclic movement maintaining adhesion and cohesion j257 repeated exposure to laboratory accelerated weathering procedures.
Follow Us facebook linkedin youtube.
This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials. This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films less than 1. Selection of the methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller.
This practice covers specific procedures and test conditions that are applicable for xenon-arc exposure of ink jet media prints conducted in accordance with Practices G and G This specification covers flexible sheet made from ethylene-propylene-diene terpolymer EPDM intended for use in single-ply roofing membranes exposed to the weather. Send us a request Wilton UK: This standard describes procedures for the determination of the relative lightfastness and weatherability of printed matter under the following conditions, which involve exposure to natural daylight or accelerated procedures in the laboratory.
Products must meet stringent performance requirements of OEM Original Equipment Manufacturersand constantly need to be improved to withstand more extreme weather conditions and achieve ever longer lifetimes.
Austest Laboratories now offers UV testing of components and plastics for lightfastness, colourfastness, and photostability in a new Xenon Arc chamber reproducing the entire spectrum of sunlight, including ultraviolet UVvisible light and infrared IR from nm to nm. This practice covers specific procedures and test conditions that are applicable for exposure of plastics in window glass-filtered xenon-arc devices in accordance with Practices G and G for evaluating the stability of plastics intended for use in indoor applications.